Some questions
47 posts
• Page 2 of 5 • 1, 2, 3, 4, 5
Re: Some questions
by krzak » Tue May 10, 2011 1:06 pm
Great, but I think, however, first try of the 4051st I am not worried about the availability of BAT85, or other elements. I mean just that a large number components, and holes to be drilled. Pads are not large, and after drilling may be very small, making it difficult to solder. Maybe it would be possible to avoid increasing the pads.
- krzak
- Posts: 24
- Joined: Tue May 10, 2011 9:56 am
Re: Some questions
by krzak » Tue May 10, 2011 8:18 pm
The last question to finish on the choice of tiles version. If I had 74hc4851, then would you recommend the version with two boards? I ask because I wonder if you recommend it only because of the difficult availability of chips, or also for another reason?
- krzak
- Posts: 24
- Joined: Tue May 10, 2011 9:56 am
Re: Some questions
by dmitri » Tue May 10, 2011 9:00 pm
The PCBs from viewtopic.php?f=3&t=266 are developed and tested by me and match the up-to-date schematic. Ultimately it is up to you which PCB to choose, you can even take the schematic in the Kicad format from the same topic and develop your own PCB layout.
- dmitri
- Site Admin
- Posts: 8709
- Joined: Fri Aug 03, 2007 8:05 pm
Re: Some questions
by krzak » Sun May 15, 2011 9:15 am
Is it necessary to use resistors with a tolerance of 1%, as some of the lists of components, or can I use resistors with a tolerance of 5%? Does the use of resistors with a power 0.125W, 0.25W, 0.5W is without a difference?
- krzak
- Posts: 24
- Joined: Tue May 10, 2011 9:56 am
Re: Some questions
by krzak » Tue May 24, 2011 7:59 pm
How should be set to the bit of security, and fuses in Avr Studio 4 for Atmega644 with 20Mhz crystal? Can I ask to screen with the correct selected?
If it has any meaning, it wants to say that I wants to upload last unencrypted firmware without a bootloader, which is not needed, because I can upload only one version of firmware.
If it has any meaning, it wants to say that I wants to upload last unencrypted firmware without a bootloader, which is not needed, because I can upload only one version of firmware.
- krzak
- Posts: 24
- Joined: Tue May 10, 2011 9:56 am
Re: Some questions
by dmitri » Tue May 24, 2011 8:49 pm
You could have search the forum and you would have found viewtopic.php?p=7281#p7281
Without a bootloader you can disable the BOOTRST fuse.
Without a bootloader you can disable the BOOTRST fuse.
- dmitri
- Site Admin
- Posts: 8709
- Joined: Fri Aug 03, 2007 8:05 pm
Re: Some questions
by krzak » Tue May 24, 2011 9:05 pm
Yes I know, but thank you for your help. In that case I will not program the BOOTRST fuse if it's not necessary.
One more question, I should first set the fuses, or upload the firmware? Or is it not matter?
Regards.
One more question, I should first set the fuses, or upload the firmware? Or is it not matter?
Regards.
- krzak
- Posts: 24
- Joined: Tue May 10, 2011 9:56 am
Re: Some questions
by dmitri » Wed May 25, 2011 9:35 am
krzak wrote:One more question, I should first set the fuses, or upload the firmware? Or is it not matter?
First firmware than fuses.
- dmitri
- Site Admin
- Posts: 8709
- Joined: Fri Aug 03, 2007 8:05 pm
Re: Some questions
by krzak » Wed May 25, 2011 10:05 am
To make sure that every fuses is set correctly I put a screen.
I have a problem with the lock bits, because I do not know how to set them. Possibilities are in the attached picture.
I have a problem with the lock bits, because I do not know how to set them. Possibilities are in the attached picture.
You do not have the required permissions to view the files attached to this post.
- krzak
- Posts: 24
- Joined: Tue May 10, 2011 9:56 am
Re: Some questions
by dmitri » Wed May 25, 2011 10:25 am
Fuses FC, 35, DF or FC, 35, D7
Lock bits leave as default, i.e. FF.
Lock bits leave as default, i.e. FF.
- dmitri
- Site Admin
- Posts: 8709
- Joined: Fri Aug 03, 2007 8:05 pm
47 posts
• Page 2 of 5 • 1, 2, 3, 4, 5
Who is online
Users browsing this forum: No registered users and 56 guests