Help

Discussions related to MegaDrum Hardware

Help

Postby anirudh.pianist » Tue Jun 07, 2011 2:35 am

Should V Do Both The PCB's tat is analogue and digital?
can som1 help me on how to make atmega32 bootloaded with my own programmer.?how r the connections of digital boards connected to alalogue and vice versa?
plz som1 help!!!




Thank U,
Ani :idea:
anirudh.pianist
 
Posts: 42
Joined: Sat Jun 04, 2011 9:41 am

Re: Help

Postby dmitri » Tue Jun 07, 2011 6:26 am

anirudh.pianist wrote:Should V Do Both The PCB's tat is analogue and digital?

Yes.

can som1 help me on how to make atmega32 bootloaded with my own programmer.?

There is no point in programming the unprotected bootloader. You cannot program the protected bootloader yourself.

how r the connections of digital boards connected to alalogue and vice versa?

According to the pin out on the schematics of both the Analogue and Digital board.
dmitri
Site Admin
 
Posts: 8709
Joined: Fri Aug 03, 2007 8:05 pm

Re: Help

Postby anirudh.pianist » Wed Jun 08, 2011 12:25 am

i hav an atmega32..not bootloaded but i hav made it run like led programs and a bldc project...how to get it bootloaded?
Can u giv me a good photo of analogue board components placment like the top silk..?
plz....


BTW,
Thanks,
Sir Dmirti :)



Bye,
Ani
anirudh.pianist
 
Posts: 42
Joined: Sat Jun 04, 2011 9:41 am

Re: Help

Postby dmitri » Wed Jun 08, 2011 11:00 am

anirudh.pianist wrote:i hav an atmega32..not bootloaded but i hav made it run like led programs and a bldc project...how to get it bootloaded?

As I said, you cannot get the protected bootloader onto your Atmega yourself. You can get an Atmega with a protected bootloader from me. See viewtopic.php?f=3&t=1552 for an example.

Can u giv me a good photo of analogue board components placment like the top silk..?

The components placement for all boards is in viewtopic.php?f=3&t=266 in relevant PDF files.
dmitri
Site Admin
 
Posts: 8709
Joined: Fri Aug 03, 2007 8:05 pm

Re: Help

Postby anirudh.pianist » Wed Jun 08, 2011 11:08 am

Ok Fine while soldering diodes...should v solder by polarity ie to the mark on pcb=mark on bat85??
anirudh.pianist
 
Posts: 42
Joined: Sat Jun 04, 2011 9:41 am

Re: Help

Postby dmitri » Wed Jun 08, 2011 11:27 am

anirudh.pianist wrote:Ok Fine while soldering diodes...should v solder by polarity ie to the mark on pcb=mark on bat85??

You must solder all diodes according to polarity.
dmitri
Site Admin
 
Posts: 8709
Joined: Fri Aug 03, 2007 8:05 pm

Re: Help

Postby anirudh.pianist » Wed Jun 08, 2011 12:14 pm

In the component list of digital board..it says order=value.
For Eg:
order is 100 and value is R2...does tat mean the value of Resistor 2 is 100 ohms?Which software do u best recommend to me to use in pc to connect?addictive drums is fine?
Last edited by anirudh.pianist on Wed Jun 08, 2011 12:22 pm, edited 1 time in total.
anirudh.pianist
 
Posts: 42
Joined: Sat Jun 04, 2011 9:41 am

Re: Help

Postby dmitri » Wed Jun 08, 2011 12:18 pm

anirudh.pianist wrote:In the component list od digital board..it says order=value.
For Eg:
order is 100 and value is R2...does tat mean the value of Resistor 2 is 100 ohms?

Yes.
dmitri
Site Admin
 
Posts: 8709
Joined: Fri Aug 03, 2007 8:05 pm

Re: Help

Postby anirudh.pianist » Wed Jun 08, 2011 4:39 pm

I felt edrum.info project is a bit simple...but in that project can i do the same thing like in urs tat is connect to computer via usb and all?
anirudh.pianist
 
Posts: 42
Joined: Sat Jun 04, 2011 9:41 am

Re: Help

Postby dmitri » Wed Jun 08, 2011 5:44 pm

anirudh.pianist wrote:I felt edrum.info project is a bit simple...

Too simple? More simple? Simple to build?...

but in that project can i do the same thing like in urs tat is connect to computer via usb and all?

Isn't it better to ask at edrum.info?
dmitri
Site Admin
 
Posts: 8709
Joined: Fri Aug 03, 2007 8:05 pm

Next

Return to MegaDrum Hardware

Who is online

Users browsing this forum: Bing [Bot], Google [Bot], Majestic-12 [Bot] and 90 guests