Note & AltNote ...

[drumdhiver]

Hello,

I have a little problem : when I'm playing, I have an altnote send just after a note, It's sound like a "fla" (or "flee", I don't know if it's correct in english?)
while I'm just hit one time...

How to configure it?

[dmitri]

Set AltNote equal to Note.

[drumdhiver]

Hi Dimitri!

Thank for reply,

Yes, I try to set "altnote" as the same number as "note", moreover, I can tick "set link to note" : "fla" effect is always present.

I'd try to disable altnote only on my VSTi, and link pressrollnote to note; I changed for different Pressroll timeout values (it's the first time I used this function). I've no more "fla", but I don't have the same "response" like I got before, it seems to be poor of sensitivity.

Ha! I've another question ! I have 2 computers, I've megadrumManager on this two one. On one of them, I have new functions (I don't know what is it?!), under Minscan :
- Pos Level : Disabled (or I can choose 1,2 or 3)
- Pos Low : 5
- Pos High : 15

Is this parameters works with my ARM 32 ? (firmware V 20121216)

[dmitri]

Hi Dimitri!

Thank for reply,

Yes, I try to set "altnote" as the same number as "note", moreover, I can tick "set link to note" : "fla" effect is always present.

Do you send the settings to MegaDrum after you've changed them in MDM?

I'd try to disable altnote only on my VSTi, and link pressrollnote to note; I changed for different Pressroll timeout values (it's the first time I used this function). I've no more "fla", but I don't have the same "response" like I got before, it seems to be poor of sensitivity.

Ha! I've another question ! I have 2 computers, I've megadrumManager on this two one. On one of them, I have new functions (I don't know what is it?!), under Minscan :
- Pos Level : Disabled (or I can choose 1,2 or 3)
- Pos Low : 5
- Pos High : 15

Is this parameters works with my ARM 32 ? (firmware V 20121216)

Yes, of course but it usable only if your MegaDrum has Positional sensing addon board built-in. I also advise you to upgrade your MegaDrum to the latest firmware version.

[drumdhiver]

Hi Dimitri,

what is a "positional sensing board built-in"?

Could you send to me a screenshot or a conf of your personal MD ARM, just for see which values you set on your parameters?

could you explain how act the minscan parameter? I read it on your documentation, but i don't really understood

regards

[dmitri]

Hi Dimitri,

what is a "positional sensing board built-in"?

About Positional sensing board read http://www.megadrum.info/forums/viewtop ... f=3&t=2052

Could you send to me a screenshot or a conf of your personal MD ARM, just for see which values you set on your parameters?

I don't have any personal MD. I have a bunch of different boards with different MCUs. Sure I can show you a screenshot of some test config:

Snap 2013-03-13 at 13.21.32.png

could you explain how act the minscan parameter? I read it on your documentation, but i don't really understood

Because I don't know what you don't understand I can only repeat what I wrote in the documentation. The main purpose of MinScan is to make sure MegaDrum samples the whole first half-wave without sacrificing latency for different types of pads. Different pads produce different length of the first half-wave.

[drumdhiver]

Hi, Dimitri,

Ok for Minscan and Positional sensing board

I will learn from your settings...

I've mesh & single piezo for snare toms and kick and I'm thinking about buying to you this card to add on my module (I check if i get it last 10 minutes)... Does it could solve my problems of "note&altnote"?

[dmitri]

I've mesh & single piezo for snare toms and kick and I'm thinking about buying to you this card to add on my module (I check if i get it last 10 minutes)... Does it could solve my problems of "note&altnote"?

Positional sensing board has nothing to do with your Note/AltNote problem. I just tried sending settings to MegaDrum from MDM with various Note/AltNote/PressrollNote and MegaDrum gets those settings fine. Can you give me step-by-step instruction to reproduce your problem?

[drumdhiver]

Dear Dimitri!

I realized that my four toms and kick get good response; my note/altnote "fla" 's problem were live on my snare. actually, It seems to came from two facts :

- the sensor position, too far from the mesh, it's a piezo with a mousse (or moss in english? i don't know), which one wasn't enough pressed relative to others

- the mesh skin wasn't strained enough (and no homogeneous tension)



I hope I do not get you too disturb with my questions!

I will send photos/videos of my kit soon, I'm very satisfied and proud of it

[dmitri]

I'm confused do you still have the problem or it's gone? If you still have the problem, what is this problem exactly?