Franken-Kit 1.0

Discussions related to MegaDrum Hardware

Re: Franken-Kit 1.0

Postby dmitri » Mon Aug 22, 2016 8:34 pm

Several people built mallet type instruments using MegaDrum. Basically MegaDrum will work with any electronic percussion instruments which use piezo triggers.
LDeVose2 wrote:3. HOW DO YOU BUY MEGADRUM!?! Or maybe it is not sold to Yankees?

Since you want to build a mallet type instrument then it is probably better to use one of MegaDrum kits - http://www.megadrum.info/forums/viewtop ... f=3&t=1420 - choose a kit version you want and then you can PM me to order.
dmitri
Site Admin
 
Posts: 8706
Joined: Fri Aug 03, 2007 8:05 pm

Re: Franken-Kit 1.0

Postby shaugnd » Tue Sep 06, 2016 3:27 am

MegMalletRex is a DIY 'electronic marimba' project that I started a couple years ago and then shelved due to a fairly serious injury. I have been progressing with recovery from a surgical procedure which has sorted things out, mostly. It has been a long road, but I'm finally to the point of dusting off this build and pushing it across the finish line.

The name comes from Mega in MegaDrum, Mallet (for obvious reasons), and Rex because it is constructed mostly of Bosch Rexroth Structural Aluminum framing. Presently it is a little over an octave. The bars are 22.5mm thick 40mm wide and 120mm long.

KeyBar22.5x45.jpg


The piezo is attached to the bottom of the bar with adhesive and wired through a hole drilled in the bottom of the bar to a 1/4" jack which slides into the hole at the bar end. The striking surface is a quarter inch thick pad which very much resembles the material used for mouse pads from the 90's. Today it is sold as a drum muffling practice pad. I got a few and cut them up.

I have changed up the design a bit from the previous approach. I am still using Marimba cording to mount the bars and reduce cross talk, but I am running it lengthwise through the channel on each side of the bar rather than through the bar. Basically this avoids more machining of the bar and doesn't interfere with the internal wiring as the previous approach did.

I am using the 56 input MegaDrum which will "read" the impact of the stick on the bar, and then send a message over MIDI to Native Instruments Komplete running on a PC, or a Roland HPD-15, for sound generation.

If I were doing this commercially, I would most certainly NOT use a MegaDrum56. That would be silly. No disrespect to Dimitri who provides a fine product and service this community, but the full MD56 is just bigger than necessary for this sort of project. Frankly, most of the size of the MD is to have space for the 1/4" jacks. If you didn't need those, then you could put it in a VHS tape size form factor. I'd get Dimitri's MegaDrum kit and build it into an enclosure designed into the overall structure of the instrument. However, I happen to know that I might feel the urge to repurpose some or all of those inputs at some point, so I use the MD56 to allow more flexibility down the line. By the way, my MD is soooo old, I don't even know what chip is in it. Heck, the firmware is from 2012 at some point I am going to have to upgrade that, but I have to figure out what chipset it is using first, so that I follow the right directions.

Lots to do on this. I'm hoping to make some headway on it this week and next.

If you have further questions, I will do my best to answer them.
You do not have the required permissions to view the files attached to this post.
shaugnd
 
Posts: 20
Joined: Tue Mar 20, 2012 1:17 am

Re: Franken-Kit 1.0

Postby airflamesred » Tue Sep 06, 2016 4:37 pm

From my experience, 2 octaves would be a minimum, but see how you get on. Glad to hear you are recovering.

koby drums - Triggera krigg/Bix - megadrum - Kontakt........... Samples from all and sundry.
airflamesred
 
Posts: 1197
Joined: Fri Mar 30, 2012 1:58 pm
Location: Hammersmith

Previous

Return to MegaDrum Hardware

Who is online

Users browsing this forum: Bing [Bot] and 103 guests