part substitution

[hartl0602]

Hello; i'm finnally getting around to making my megadrum; but i'm hitting a snag in the parts aquisition. the following parts are on backorder, and i was wondernig if anyone knows of a sub? also has anyone used the diy echant that is recomended on the 2.5 boards parts list?

Mouser #: 103-1113-EVX

Mfr. #: 103-1113-EVX

Desc.: Pushbutton Switches MTL BDY BLK STM/CAP

RoHS: RoHS Compliant By Exemption
Product Update: View Product Update



________________________________________
Availability
0 Ships Now
4 Backordered

$1.09 $4.36

Mouser #: 568-NYS325

Mfr. #: NYS325

Desc.: DIN Connectors FEMALE 5-PIN CHASSIS

RoHS: RoHS Compliant


________________________________________
Availability
0 Ships Now
2 Backordered

$0.74 $1.48

Mouser #: 568-NYS215

Mfr. #: NYS215

Desc.: Phone Jacks 1/4 STEREO SWITCHED

RoHS: RoHS Compliant


________________________________________
Availability
0 Ships Now
17 Backordered

$0.75 $12.75

Mouser #: 71-CCF07100RJKE36

Mfr. #: CCF07100RJKE36

Desc.: 1/4WATT Metal Film Resistors 1/4watt 100ohms 5% Rated to 1/2watt

RoHS: RoHS Compliant


________________________________________
Availability
0 Ships Now
1 Backordered

$0.02 $0.02

Mouser #: 140-50N5-220J-TB-RC

Mfr. #: 140-50N5-220J-TB-RC

Desc.: Class 1 Ceramic Disc Capacitors - Tape/Box 50V 22pF NPO 5% Tol

RoHS: RoHS Compliant


________________________________________
Availability
0 Ships Now
2 Backordered

$0.06 $0.12

[jamdat]

Hello; i'm finnally getting around to making my megadrum; but i'm hitting a snag in the parts aquisition. the following parts are on backorder, and i was wondernig if anyone knows of a sub? also has anyone used the diy echant that is recomended on the 2.5 boards parts list?

I know for sure that the kind of resistor/capacitor you get makes no difference. As long as the value is the same (eg: 100ohm/22pf) and it fits on the board, you're good to go. Same deal eith the switch. A switch is a switch is a switch. If it meets whe requirements (momentary on, etc) use it. Same with the plugs. As I've learned, you're not forced to get those part numbers.

[hartl0602]

right but with the jacks in peticular is one better than the other, do i need to worry about shield jacks? or can i just get any old stero jack?

[jamalpiper]

With jacks, the only thing I would really worry about is size and mounting style. Size so it fits correctly into your enclosure, and mounting style so you don't buy PCB mount Jacks when you needed solder pads.

[hartl0602]

cool...placed my order as for enclosure space, no biggie...i'm making my own

still curious though if anyone has tried the diy etchent

[gastric]

I used the DIY etchant and it works as described. You still need to agitate the board in the acid to keep the copper from sitting in a layer on top of the board. I just stuck it in a Tupperware type container with the lid on and gently shook the whole thing back and forth. Took about 15-20 minutes to completely etch the main board. Of course take normal safety precautions like goggles and gloves.

[hartl0602]

so what is the ratio of muriatic acid to peroxide?

[gastric]

Go to this excellent PCB making page: http://www.fullnet.com/~tomg/gooteepc.htm

And scroll down to the section titled "NEW ETCHANT UPDATE"

[hartl0602]

one last question (for now); can someone give me a mesurement corner to corner of both their main board and thier jacks board (corner mounting hole to corner mounting hole center to center or close to it) i'm trying to get my scale right...but it eludes me.